ScholarMate
English简体中文繁體中文
客服热线:400-1616-289
登录注册
期刊论文

3D printed PLGA/MgO/PDA composite scaffold by low-temperature deposition manufacturing for bone tissue engineering applications

Tan, Liang; Ye, Zhuofeng; Zhuang, Weida; Mao, Beini; Li, Hetong; Li, Xiuwang; Wu, Jiachang; Sang, Hongxun*南方医科大学
Regenerative Therapy2023-12DOI: 10.1016/j.reth.2023.09.015
8阅读
引用收藏
分享

摘要

Introduction: Bones are easily damaged. Biomimetic scaffolds are involved in tissue engineering. This study explored polydopamine (PDA)-coated poly lactic-co-glycolic acid (PLGA)-magnesium oxide (MgO) scaffold properties and its effects on bone marrow mesenchymal stem cells (BMSCs) osteogenic differentiation.Methods: PLGA/MgO scaffolds were prepared by low-temperature 3D printing technology and PDA coatings were prepared by immersion method. Scaffold structure was observed by scanning electron microscopy with an energy dispersive spectrometer (SEM-EDS), fourier transform infrared spectrometer (FTIR). Scaffold hydrophilicity, compressive/elastic modulus, and degradation rates were analyzed by water contact angle measurement, mechanical tests, and simulated-body fluid immersion. Rat BMSCs were cultured in scaffold extract. Cell activity on days 1, 3, and 7 was detected by MTT. Cells were induced by osteogenic differentiation, followed by evaluation of alkaline phosphatase (ALP) activity on days 3, 7, and 14 of induction and Osteocalcin, Osteocalcin, and Collagen I expressions.Results: The prepared PLGA/MgO scaffolds had dense microparticles. With the increase of MgO contents, the hydrophilicity was enhanced, scaffold degradation rate was accelerated, magnesium ion release rate and scaffold extract pH value were increased, and cytotoxicity was less when magnesium mass ratio was less than 10%. Compared with other scaffolds, compressive and elastic modulus of PLGA/MgO (10%) scaffolds were increased; BMSCs incubated with PLGA/MgO (10%) scaffold extract had higher ALP activity and Osteocalcin, Osteopontin, and Collagen I expressions. PDA coating was prepared in PLGA/MgO (10%) scaffolds and the mechanical properties were not affected. PLGA/MgO (10%)/PDA scaffolds had better hydrophilicity and biocompatibility and promoted BMSC osteogenic differentiation.Conclusion: Low-temperature 3D printing PLGA/MgO (10%)/PDA scaffolds had good hydrophilicity and biocompatibility, and were conducive to BMSC osteogenic differentiation.(c) 2023, The Japanese Society for Regenerative Medicine. Production and hosting by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/ 4.0/).

学科与关键词

关键词
Low-temperature three-dimensionalprintingPoly lactic-co-glycolic acidMagnesium oxidePolydopamineScaffold materialsBone marrow mesenchymal stem cellOsteogenic differentiationPhysical and chemical properties
相关
加载中…
  • Immobilizing magnesium ions on 3D printed porous tantalum scaffolds with polydopamine for improved vascularization and osteogenesis
    Ma, Limin; Cheng, Shi; Ji, Xiongfa; Zhou, Ye; Zhang, Yusong; Li, Qingtao; Tan, Chaohui; Peng, Feng*; Zhang, Yu; Huang, Wenhua*MATERIALS SCIENCE & ENGINEERING C-BIOMIMETIC AND SUPRAMOLECULAR SYSTEMS, 2020, 117: 111303.被引 45
  • 3D printed polycaprolactone/beta-tricalcium phosphate/magnesium peroxide oxygen releasing scaffold enhances osteogenesis and implanted BMSCs survival in repairing the large bone defect
    Peng, Ziyue; Wang, Chengqiang; Liu, Chun; Xu, Haixia; Wang, Yihan; Liu, Yang; Hu, Yunteng; Li, Jianjun; Jin, Yanglei; Jiang, Cong; Liu, Liangle; Guo, Jiasong*; Zhu, Lixin*Journal of Materials Chemistry B, 2021, 9(28): 5698-5710.被引 29
  • MgO-incorporated porous nanofibrous scaffold promotes osteogenic differentiation of pre-osteoblasts
    Wang, Xiaoyu; Liu, Mingyue; Li, Haiyan; Yin, Anlin; Xia, Changlei; Lou, Xiangxin; Wang, Hongsheng; Mo, Xiumei; Wu, Jinglei*Materials Letters, 2021, 299: 130098.
查看全部 →

发表信息

论文状态
公开发表
期刊
Regenerative Therapy
发表日期
2023-12
卷期
第 24 卷
页码
617-629
DOI
10.1016/j.reth.2023.09.015
成果收录
SCIE
资助标注
National Natural Science Founda- tion of China [81871767]; Shenzhen Key Laboratory of Digital Surgical Printing Project [ZDSYS201707311542415]; Shenzhen Sci- ence and Technology Program [JCYJ20220818103417037]; Shenz- hen Development and Reform Program [XMHT20220106001]

作者

  • T

    Tan, Liang (第一作者)

    southern med univ

  • Y

    Ye, Zhuofeng

查看全部 8 位作者收起作者
  • Z

    Zhuang, Weida

    southern med univ

  • M

    Mao, Beini

    southern med univ

  • L

    Li, Hetong

    southern med univ

  • L

    Li, Xiuwang

    southern med univ

  • W

    Wu, Jiachang

    southern med univ

  • S

    Sang, Hongxun (通讯)

    southern med univ

登录解锁更多功能

  • 收藏这篇,随时在“我的 · 收藏”找回
  • 认领你的成果,生成推广素材
  • 关注作者获取最新成果
  • 加入项目组、协同写作
注册 / 登录

产品服务

  • 科研之友
  • 创新城
  • 科创云

服务支持

  • 帮助中心
  • 隐私政策
  • 服务条款

联系方式

在线客服:【】
客服热线:400-1616-289
电子邮箱:support@scholarmate.com

关注或下载科研之友

微信二维码
微信公众号
客户端下载二维码
下载客户端
科研成果科研人员科研机构科研动态爱瑞思软件

©2026 深圳市科研之友网络服务有限公司

公安备案图标粤公网安备 44030502000213
粤ICP备 16046710 号粤B2-20110417